The Compleat Sculptor
" You supply the talent, we'll supply the rest!" Since 1995
Click here to order
QUIKWOOD® Wood Repair Epoxy Putty
Product Description - QUIKWOOD® is a hand-mixable, NON-SHRINKING, filled epoxy putty which when cured becomes an integral part of the wooden item being repaired, rebuilt, or restored. One hour after mixing, QUIKWOOD® can be drilled, sawed, sanded, filed, tapped, machined, or painted. It comes in a handy, 2 oz. "tootsie roll" form with the curing agent encapsulated in the contrasting color base material. The putty-like consistency eliminates drips and runs, providing "no mess" applications with no tools required for use. QUIKWOOD® belongs in every toolbox.
 
Basic Uses - After proper mixing, QUIKWOOD® molds like clay to repair, rebuild, or restore anything made of wood. It fills nail and screw holes, gouges, and scratches, and replaces rotten and worn wood. It repairs moldings, panel frames, and furniture, including leveling table and chair legs. QUIKWOOD® can be used to reshape wood carvings and wood parts such as handles, knobs, and pulls. It can also be used as an adhesive in making general wood to wood, and wood to metal bonding. QUIKWOOD® contains no solvents, will not shrink, pull away, or dry out and is non-toxic. QUIKWOOD® may be used in interior and exterior applications as it is virtually unaffected by weather. Sanding of cured QUIKWOOD® may be used in interior and exterior applications as it is virtually unaffected by weather. Sanding of cured QUIKWOOD® is recommended prior to applying paint or stain, QUIKWOOD® may accept stain differently than wood. Test before using. The unused portion of QUIKWOOD® will remain stable for years if stored in its container at room temperature.
Color - Simulated wood color after cure.
Packaging - QUIKWOOD® is packed in a reusable clear plastic tube with a plastic friction top.
 
Technical Data: Refer to table for typical properties*
*for information only – not for specification purposes
Application
Properties Results
Test Method
Work Life, minutes
15 - 25
Shelf Stability @ 75ºF
Months (minimum)
12
Hardness, Shore D
(Full cure, 24 hours)
65 - 75
ASTM D-2240
Lap Shear Tensile Strength
on Steel (1" x 1" x 1/16"), lbs.
400 - 600
ASTM D-1002
Temperature Limitations, ºF
Continuous
250
Intermittent
300
Chemical Resistance

Resistance to hydrocarbons, ketones, alcohols, esters, halocarbons, aqueous salt solutions, and dilute acids and bases.

Electrical Resistance, megohms
30,000
Dielectric Strength, volts/mil
300
ASTM D-257
Shrinkage, %
<1
ASTM D-149
Non-Volatile Content, %
100
ASTM D-2566
Compression Strength, lbs/in²
12,000
ASTM D-695
Application

Surface Preparation:
In order to achieve optimum adhesion, surfaces should be clean and free of grease and dirt. Scuffing or sanding the surface prior to cleaning helps ensure a good bond.
Mixing:
Twist or cut off required amount. To mix, knead with fingers to a uniform color. If mixing is difficult, warm QUIKWOOD® to a room temperature of slightly above. Apply to the surface to be repaired (within 15-20 minutes of mixing). Force into any cracks or holes to be filled and strike off excess material, preferably with a tool wetted with clean water. When applying to a damp, wet, or slowly leaking area, work he material forcefully into the surface and apply pressure until adhesion begins to take effect.
For a smooth appearance of the cured compound, hand rub with water or a damp cloth prior to hardening. Remove excess material before hardening begins. After 15-20 minutes the epoxy will begin to form a tenacious bond. After just 60 minutes QUIKWOOD® can be drilled, sawed, carved, sanded, stained, or painted.
Health Precautions - When mixing by hand, QUIKWOOD ® does not cause skin irritation to individuals with normal skin sensitivity. Individuals with extra sensitive skin should maintain caution and wash hands thoroughly after mixing the compound, or wear thin plastic gloves. QUIKWOOD ® has been classified non-toxic and non-skin irritating when tested versus the requirements of the Federal Hazardous Substances Labeling Act.
Warning
  1. May cause irritation to sensitive skin. Wash hands with soap and water after use.
  2. Eye irritant. In case of eye contact, flush with water. Contact physician.
  3. May be harmful if swallowed.
  4. Keep out of reach of children.
  5. Not intended for use in structural applications.
  6. When sanding cured putty or substrate, use protective eye wear and dust mask.
Warranty - All recommendations, statements and technical data contained herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed of implied. User shall rely on his own information and tests to determine suitability of the product for intended use, and user assumes all risk and liability resulting from the use of this product.
Manufacturer’s sole responsibility shall be to replace that portion of the product of the manufacturer which proves to be defective. Manufacturer shall not be liable to the buyer or any third party for injury, loss or damage directly or indirectly resulting from use of, or inability to use the product.
Recommendations or statements other than those contained in a written agreement signed by an officer of the manufacturer shall not be binding upon the manufacturer.

Although we try to keep the most updated prices on our website, all prices are subject to change.
1-800-9-SCULPT
-
-